Zebra-technologies Cameo Portable Encoding Printer Bedienungsanleitung Seite 1

User's ManualPortable Encoding PrinterPart No. UMAN-PEP Rev J, January, 2004

10UMAN-PEPINSTALLATION OF MEDIAThe following details media installation:1. Turn unit off.2. Squeeze the two finger grips on either side of themedia c

11UMAN-PEPFeed media inthis directionEdge GuideSqueeze fingergrips here onboth sides toopen coverINSTALLATION OF MEDIA IN THE CAMEO PEPInsert EdgeGuid

12UMAN-PEPMAINTENANCEThe Cameo PEP will provide reliable service if a fewsimple guidelines are followed. The printer should becleaned approximately e

13UMAN-PEPMedia SensorPrint HeadPlatenCLEANING THE CAMEO PEP

14UMAN-PEPMAGNETIC CARD ENCODER (MCE)The magnetic stripe reader/encoder is used as follows:Reading Cards1.A flashing status light indicates the printe

15UMAN-PEPStripe faces this wayUSING THE CAMEO PEP MAGNETIC CARD ENCODERSlide card in this direction

16UMAN-PEPCOMMUNICATING TO THE PRINTERThe printer must establish communications with a hostterminal which sends the data to be printed. Communi-catio

17UMAN-PEPcontinued next pageIR CommunicationsPrinters equipped for infrared (IR) communications areidentified by a small “IR” logo on the unit’s keyp

18UMAN-PEPBluetooth™ Networking Overview“Bluetooth” is a worldwide standard for the exchange ofdata between two devices via radio frequencies.Bluetoot

19UMAN-PEPAddress (BDA) loaded into its radio module when manu-factured.A Typical Bluetooth Connection SequenceIn this simplified sequence “Joe’s Ter

Proprietary StatementThis manual contains proprietary information of Zebra Technologies Corporation. It isintended solely for the information and use

20UMAN-PEPTROUBLESHOOTINGSelf Test:Perform the self test as described in the Controls sec-tion. Unit should print a line of interlocking “x” charact

21UMAN-PEP• Invalid label format or command structure — use Hex DumpMode for troubleshooting.Reduced battery charge life:• Recondition (cycle) battery

Appendices

A-1APPENDIX AINTERFACE CABLESPin 1Pin 9DB-9 PinFemale Plug(to P.C.)8 PinMale Plug(to printer)(TXD)(RXD)(RTS)(CTS)(GND)(DTR)(DSR)Shield(RXD)(TXD)(CTS)

A-2APPENDIX AINTERFACE CABLESCable Cord Terminal PrinterTerminal Part Number Lgth/Type Connector Connector NotesCOMPSEEApex II BL12093-3 8’ Coiled RJ

APPENDIX AINTERFACE CABLES (continued)A-3Cable Cord Terminal PrinterTerminal Part Number Lgth/Type Connector Connector NotesSYMBOL (CONT.)LRT/LDT3800

A-4APPENDIX BMEDIA SUPPLIESTo insure maximum printer life and consistent print qualityand performance for your individual application, it isrecommend

A-5APPENDIX CMAINTENANCE SUPPLIESIn addition to using quality media provided by Zebra, it isrecommended that the print head be cleaned as pre-scribed

A-6APPENDIX DPRODUCT SUPPORTFor product support, contact Zebra Technologies at:www.zebra.comZebra Technologies International, LLC333 Corporate Woods P

A-7D275,286D347,021D389,178D430,199D433,7023,964,6734,019,6764,044,9464,360,7984,369,3614,387,2974,460,1204,496,8314,593,1864,607,1564,673,8054,736,09

CONTENTSIntroduction ... 5Controls ...

4UMAN-PEPTHE CAMEOTM PEP PORTABLE ENCODING PRINTERMagnetic Stipe Card reader/EncoderKeypadMedia CoverSerialCommunicationsPortBattery LatchIR window(fo

5UMAN-PEPINTRODUCTIONThe Cameo™ PEP Portable Encoding Printer combinesthe latest technology in direct thermal printing with theability to read and en

6UMAN-PEPCONTROLSKeypad FunctionsSelf TestCameo PEP can perform a self test which will print aline of interlocking “x” characters to insure all ele-me

7UMAN-PEPBATTERIES AND CHARGINGBattery terminals are recessed to prevent acci-dental short circuitingof the battery. Allow-ing these terminals tocont

8UMAN-PEPConditioning Battery PacksIMPORTANTCameo batteries must be cycled several timesbefore maximum capacity is realized.A battery is ”cycled” by

9UMAN-PEPLow Battery ShutdownThe Cameo PEP monitors the battery charge level insoftware and will cause the Power LED to flash as thebattery becomes de